Scope Mount

FireRat · December 18th, 2008, 06:59

I need something to raise the scope up another half inch or so. Is there some kind of rail that attaches to the existing rail to make the scope sit higher? I duno really how else to explain it so I hope this works, I have a picture I can show of the scope and the gun. The scope sits on the rail basically and I can't turn the focus so I need it to be higher.

Kuro_Neko · December 18th, 2008, 08:59

Yup. They're called raisers. Take a look Here. Or if that's not high enough you could go with something like This. That's alittle pricey though. If that kind of height is what you're after then you might be better off getting a Carry Handle (which you can get much cheaper in the classifieds then is listed in that link) and then using one of These.

Kuro_Neko

CDN_Stalker · December 18th, 2008, 10:51

Standard Weaver type rifles scope mounts, those look to be about medium size, high mounts (available at gun/hunting stores) would raise it up another 1/4". Best to take the mounts off and take one with you to the store to compare what yo uhave to what they have as far as height goes.

lupo · December 18th, 2008, 21:20

Or you could get higher scope rings. As those look like low rise rings.

CDN_Stalker · December 19th, 2008, 09:53

Quote:

Originally Posted by lupo

Or you could get higher scope rings. As those look like low rise rings.

Isnt' that what I just said? Lol, they aren't low ones, they are medium, low wouldn't fit that scope on a rail.

Azuki · December 19th, 2008, 12:37

Those look like airgun sight scope rings. They're for scopes that are single straight tube designs, not the tapering ones.

You could do what someone mentioned, get a carry handle, and the M16 scope mount that attaches to it.

FireRat · December 19th, 2008, 17:12

I don't want a carry handle for it I like the way it looks. I found a raiser made by madbull I am gona get and give it a try I think it will work nicely. Thanks guys ^^

lupo · December 19th, 2008, 18:19

Quote:

Originally Posted by CDN_Stalker

Isnt' that what I just said? Lol, they aren't low ones, they are medium, low wouldn't fit that scope on a rail.

Gawd , that is what you said..... I read through it all so quickly I thought you had written something else completely DOH!.
Anyways though.
I personally have a set of medium height rings that would be classified as high by any other manufacturer , so ring height can vary a bit.
Why dont you just go down to your local gun store and get a higher set of rings. Hell Canadian Tire may even sell them in thier hunting section.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

December 18th, 2008, 06:59	#1
FireRat Trader rating Join Date: Jan 2007 Location: Maple Ridge, BC	Scope Mount I need something to raise the scope up another half inch or so. Is there some kind of rail that attaches to the existing rail to make the scope sit higher? I duno really how else to explain it so I hope this works, I have a picture I can show of the scope and the gun. The scope sits on the rail basically and I can't turn the focus so I need it to be higher. __________________ Mp5K Flecktarn <:3_)~

December 18th, 2008, 10:51	#3
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Standard Weaver type rifles scope mounts, those look to be about medium size, high mounts (available at gun/hunting stores) would raise it up another 1/4". Best to take the mounts off and take one with you to the store to compare what yo uhave to what they have as far as height goes. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

December 19th, 2008, 12:37	#6
Azuki Trader rating Join Date: Sep 2008 Location: Toronto	Those look like airgun sight scope rings. They're for scopes that are single straight tube designs, not the tapering ones. You could do what someone mentioned, get a carry handle, and the M16 scope mount that attaches to it. __________________ CAPS Shooter WA SV Infinity 5" Classic

December 18th, 2008, 08:59	#2
Kuro_Neko Trader rating Join Date: Aug 2008 Location: St. John's, Newfoundland	Yup. They're called raisers. Take a look Here. Or if that's not high enough you could go with something like This. That's alittle pricey though. If that kind of height is what you're after then you might be better off getting a Carry Handle (which you can get much cheaper in the classifieds then is listed in that link) and then using one of These. Kuro_Neko

December 18th, 2008, 21:20	#4
lupo Trader rating Join Date: Dec 2001 Location: vancouver	Or you could get higher scope rings. As those look like low rise rings.

December 19th, 2008, 17:12	#7
FireRat Trader rating Join Date: Jan 2007 Location: Maple Ridge, BC	I don't want a carry handle for it I like the way it looks. I found a raiser made by madbull I am gona get and give it a try I think it will work nicely. Thanks guys ^^ __________________ Mp5K Flecktarn <:3_)~

Scope Mount

Accessories Discussion