Nine ball SAS/Strike 5.1 Kit

Qlong · February 27th, 2008, 10:36

Hello, I am flabbergasted as to how the Nine ball SAS/Strike 5.1 Kit, is attached to the 5.1, from this photo, looks like it just screws into the rail at 2 places. So just to clarify, do all 5.1 models have this threading so it can be attached, because my WE 5.1 doesn't. Thanks.

Dracheous · February 27th, 2008, 10:52

Remove the slide from your hicapa, and put it aside. Looking at the frame, look down the channel that the slide travels, just in front of the trigger guard you will see two small impressions and one screw. Carefully drill out those impressions, and the screws that hold the kit to the frame with go down those holes from the inside, "pulling" the kit tight to the frame.

If that didn't solve it, PM me and I can walk ya through it.

ILLusion · February 27th, 2008, 15:28

It is meant ONLY for Tokyo Marui 5.1.

It will not fit on to any 4.3 model or any WE gun.

If you own a Tokyo Marui 5.1, the manual will have instruction on how to install the included lower rail with the gun, and a tool is included so that you can punch out the holes required.

Batchokookies · June 11th, 2009, 00:27

Hi, sorry I know this thread is a bit dated, but I decided it was better than starting a whole new thread.

Is there any way at all that you could modify this kit to fit a 4.3 tac? I was thinking of just getting a 5.1 length outer barrel and recoil spring guide, would that work? Or do you have to have the same frame without the built-in rail?

Thanks

m102404 · June 11th, 2009, 09:35

The way it's setup, the bottom rail bolts to a 5.1 frame. That piece has a "saddle" that cups the bottom of the 5.1 slide that extends past the frame. Then there is a block that bolts onto the front end of the rail and the slide butts up against it. Just like an "L" that's laid sideways.

So...no. The "saddle" wouldn't side right anywhere on the 4.3. Even if you ground/cut it off, there wouldn't be a good way to attach it to the underside of the 4.3 frame.

You could make a "meat tenderizer" block...and just bolt it to the front of your 4.3 frame. You'd need to drill and tap two little holes to attach it. Getting it all lined up right would be pretty fiddly.

There might be something for a 4.3 kit...but I've never looked into it, sorry.

Tys

Batchokookies · June 11th, 2009, 20:58

thanks for the reply.

(sigh) I guess that complicates my decision between a 5.1 and a 4.3.

lokisama · June 11th, 2009, 21:13

There is a version that you have to use in conjunction with a 4.3 slide tho.
http://www.tokyo-model.com.hk/ecshop/goods.php?id=3598
still needs hicapa 5 as a base model.

ILLusion · June 18th, 2009, 16:23

You can do this to fit a 4.3, but you will need:

- Tokyo Marui Hi-Capa 5.1 frame (MUST be Tokyo Marui. Clones will not work)
- Mill/saw/Dremel tool or some other tool to chop down the front of the base that the spiked front mounts to
- A drill(press) to drill new holes to allow the spiked front to mate to the mount.

I've seen it done before... it looks impressive

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

February 27th, 2008, 10:36	#1
Qlong Division Trader rating Join Date: Jun 2007 Location: Scarborough, Ontario	Nine ball SAS/Strike 5.1 Kit Hello, I am flabbergasted as to how the Nine ball SAS/Strike 5.1 Kit, is attached to the 5.1, from this photo, looks like it just screws into the rail at 2 places. So just to clarify, do all 5.1 models have this threading so it can be attached, because my WE 5.1 doesn't. Thanks. __________________ Weee!

February 27th, 2008, 10:52	#2
Dracheous Lego Head Trader rating Join Date: Nov 2005 Location: Gatineau, that's right I'm in QUEBEC!	Remove the slide from your hicapa, and put it aside. Looking at the frame, look down the channel that the slide travels, just in front of the trigger guard you will see two small impressions and one screw. Carefully drill out those impressions, and the screws that hold the kit to the frame with go down those holes from the inside, "pulling" the kit tight to the frame. If that didn't solve it, PM me and I can walk ya through it. __________________ _________________________________ "The hydrogen economy car from the people who brought you the 'Hindenburg'" - Glen Foster Condoms do not guarantee safe sex any more. A friend of mine wore one and was shot by the woman's husband!

February 27th, 2008, 15:28	#3
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	It is meant ONLY for Tokyo Marui 5.1. It will not fit on to any 4.3 model or any WE gun. If you own a Tokyo Marui 5.1, the manual will have instruction on how to install the included lower rail with the gun, and a tool is included so that you can punch out the holes required. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

June 11th, 2009, 00:27	#4
Batchokookies Trader rating Join Date: Jul 2008 Location: Calgary	Hi, sorry I know this thread is a bit dated, but I decided it was better than starting a whole new thread. Is there any way at all that you could modify this kit to fit a 4.3 tac? I was thinking of just getting a 5.1 length outer barrel and recoil spring guide, would that work? Or do you have to have the same frame without the built-in rail? Thanks __________________ WE SCAR TM M14 RWC G18C KWA P226 PTP X2 VFC/UMAREX MP5A2

June 11th, 2009, 09:35	#5
m102404 Tys Trader rating Join Date: Apr 2006 Location: Toronto	The way it's setup, the bottom rail bolts to a 5.1 frame. That piece has a "saddle" that cups the bottom of the 5.1 slide that extends past the frame. Then there is a block that bolts onto the front end of the rail and the slide butts up against it. Just like an "L" that's laid sideways. So...no. The "saddle" wouldn't side right anywhere on the 4.3. Even if you ground/cut it off, there wouldn't be a good way to attach it to the underside of the 4.3 frame. You could make a "meat tenderizer" block...and just bolt it to the front of your 4.3 frame. You'd need to drill and tap two little holes to attach it. Getting it all lined up right would be pretty fiddly. There might be something for a 4.3 kit...but I've never looked into it, sorry. Tys

June 11th, 2009, 20:58	#6
Batchokookies Trader rating Join Date: Jul 2008 Location: Calgary	thanks for the reply. (sigh) I guess that complicates my decision between a 5.1 and a 4.3. __________________ WE SCAR TM M14 RWC G18C KWA P226 PTP X2 VFC/UMAREX MP5A2

June 11th, 2009, 21:13	#7
lokisama Trader rating Join Date: Oct 2007 Location: etobicoke, ON	There is a version that you have to use in conjunction with a 4.3 slide tho. http://www.tokyo-model.com.hk/ecshop/goods.php?id=3598 still needs hicapa 5 as a base model. __________________ Western Arms Infinity 6" Hybrid DX silver Limited Western Arms Infinity 5" Expert KSC MP7A1 KSC USP Match Kimber Warrior [Nova FMU kit] Kimber Gold Combat Stainless [Nova FMU kit]

June 18th, 2009, 16:23	#8
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	You can do this to fit a 4.3, but you will need: - Tokyo Marui Hi-Capa 5.1 frame (MUST be Tokyo Marui. Clones will not work) - Mill/saw/Dremel tool or some other tool to chop down the front of the base that the spiked front mounts to - A drill(press) to drill new holes to allow the spiked front to mate to the mount. I've seen it done before... it looks impressive __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

Nine ball SAS/Strike 5.1 Kit

Accessories Discussion