VFC RAS Panel

MAFIA · January 2nd, 2006, 23:22

I cant seem to remove the hanguard panels that came with my VFC M14 RAS. Any suggestions on removing this panel will be greatly appreciated

Adrian · January 3rd, 2006, 00:27

I'm guessing they're the panels here?

http://www.wgcshop.com/pcart/shopper...IS%20and%20RAS ?

Then you depress the metal strip that's at one end, and pull e'm off the rail, along the same axis that the rail runs.

MAFIA · January 3rd, 2006, 01:43

thanks for the input, however thats what I have bin doing the whole time. its just the panels are like super tightly fixed onto the rail

Eddie · January 3rd, 2006, 03:16

Yup the VFC M14 RAS has some very tight rail covers I stopped trying a while ago. I tried holding the tab down and having someone try pulling on it while I pulled the RAS in the opposite direction its really stuck on.

Adrian · January 3rd, 2006, 13:28

Quote:

Originally Posted by MAFIA

thanks for the input, however thats what I have bin doing the whole time. its just the panels are like super tightly fixed onto the rail

Oh. Well, in that case, and if you don't care too much about the rails, try putting the rails in a vice, and throw yer weight into it.

And then pick up some Magpul rails. In sexy OD. You know you want it.

Eddie · January 3rd, 2006, 16:29

OK I got bored and tried taking off again. This time I put the front of the RAS on the table with the Panel hanging off the side had some on hold the RAS upright while I pushed on the tab and took a rubber mallet and slowly knocked it off.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 2nd, 2006, 23:22	#1
MAFIA Trader rating Join Date: Dec 2002 Location: Vancouver	VFC RAS Panel I cant seem to remove the hanguard panels that came with my VFC M14 RAS. Any suggestions on removing this panel will be greatly appreciated

January 3rd, 2006, 00:27	#2
Adrian Trader rating Join Date: Dec 2001 Location: O-dot!	I'm guessing they're the panels here? http://www.wgcshop.com/pcart/shopper...IS%20and%20RAS ? Then you depress the metal strip that's at one end, and pull e'm off the rail, along the same axis that the rail runs. __________________ I want a ring. Don't you?

January 3rd, 2006, 01:43	#3
MAFIA Trader rating Join Date: Dec 2002 Location: Vancouver	thanks for the input, however thats what I have bin doing the whole time. its just the panels are like super tightly fixed onto the rail

January 3rd, 2006, 03:16	#4
Eddie Trader rating Join Date: Jun 2003 Location: Surrey, BC	Yup the VFC M14 RAS has some very tight rail covers I stopped trying a while ago. I tried holding the tab down and having someone try pulling on it while I pulled the RAS in the opposite direction its really stuck on.

January 3rd, 2006, 16:29	#6
Eddie Trader rating Join Date: Jun 2003 Location: Surrey, BC	OK I got bored and tried taking off again. This time I put the front of the RAS on the table with the Panel hanging off the side had some on hold the RAS upright while I pushed on the tab and took a rubber mallet and slowly knocked it off.

VFC RAS Panel

Doctor's Corner