Umarex HK416 Takedown?

Xtrykr · January 6th, 2012, 02:53

Hi all, there doesn't seem to be any manuals or diagrams regarding pins and such, I managed to take out the upper receiver, barrel, rail, bolt release and mag release as it was pretty standard, but not quite sure where to go from there. Is it just the motor that just need to takeout and the gearbox should just slip out? Or is there anything else I need to yank out or loosen before I do so? I'm hesitant on using any force, so just consulting any existing Umarex/VFC HK416 owners out there first

Also, the buffer tube ring, is it CW or CCW to loosen? I just need to get into the gearbox to swap a spring. Any help would be greatly appreciated, thanks! :}

Danke · January 6th, 2012, 03:00

It comes apart like any normal M4/V2 gearbox. The only tricky bit is the hold open catch.

So take the motor out, take the pistol grip off, knock out the captured pin at the rear and the drift pin over the trigger. Then remove the screw from the spring loaded part of the bolt catch and pull it off.

It wiggles out from the rear first and you're in business. Re-assemble in reverse order. The bolt catch should be hooked back up once you get the mechbox back in the receiver and then he drift pin, motor/grip, push pin and mag release.

Xtrykr · January 6th, 2012, 03:03

Wow, thanks for the quick reply Danke.

After removing the motor, I should just be able to pull the pistol grip off from the lower receiver? Or is there anything hold it down?

Danke · January 6th, 2012, 03:07

There are phillips head screws holding the grip on, 2 probably.

Xtrykr · January 6th, 2012, 11:48

Hrm, I can't seem to find the 2 phillips head screws you are referring to. Do they connect the pistol grip to the lower receiver?

Danke · January 6th, 2012, 12:17

Take off the motor plate, take out the motor. Memorize how the wires are routed. Look inside the pistol grip. Then connect the grip to the mechbox.

ShadowNet · January 6th, 2012, 12:38

the Umarex HK416 is a VFC, so takedown is the same as a VFC M4.

Xtrykr · January 6th, 2012, 12:45

Danke - Awesome, got it, thanks man! +1 rep.

Shadownet - You're right!

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 6th, 2012, 02:53	#1
Xtrykr Trader rating Join Date: Jul 2011 Location: Winnipeg	Umarex HK416 Takedown? Hi all, there doesn't seem to be any manuals or diagrams regarding pins and such, I managed to take out the upper receiver, barrel, rail, bolt release and mag release as it was pretty standard, but not quite sure where to go from there. Is it just the motor that just need to takeout and the gearbox should just slip out? Or is there anything else I need to yank out or loosen before I do so? I'm hesitant on using any force, so just consulting any existing Umarex/VFC HK416 owners out there first Also, the buffer tube ring, is it CW or CCW to loosen? I just need to get into the gearbox to swap a spring. Any help would be greatly appreciated, thanks! :}

January 6th, 2012, 03:00	#2
Danke Prancercise Guru Trader rating Join Date: Oct 2007 Location: Danger Zone	It comes apart like any normal M4/V2 gearbox. The only tricky bit is the hold open catch. So take the motor out, take the pistol grip off, knock out the captured pin at the rear and the drift pin over the trigger. Then remove the screw from the spring loaded part of the bolt catch and pull it off. It wiggles out from the rear first and you're in business. Re-assemble in reverse order. The bolt catch should be hooked back up once you get the mechbox back in the receiver and then he drift pin, motor/grip, push pin and mag release. __________________ Airsoft, where nothing is hurt but feelings.

January 6th, 2012, 03:07	#4
Danke Prancercise Guru Trader rating Join Date: Oct 2007 Location: Danger Zone	There are phillips head screws holding the grip on, 2 probably. __________________ Airsoft, where nothing is hurt but feelings.

January 6th, 2012, 03:03	#3
Xtrykr Trader rating Join Date: Jul 2011 Location: Winnipeg	Wow, thanks for the quick reply Danke. After removing the motor, I should just be able to pull the pistol grip off from the lower receiver? Or is there anything hold it down?

January 6th, 2012, 11:48	#5
Xtrykr Trader rating Join Date: Jul 2011 Location: Winnipeg	Hrm, I can't seem to find the 2 phillips head screws you are referring to. Do they connect the pistol grip to the lower receiver?

January 6th, 2012, 12:17	#6
Danke Prancercise Guru Trader rating Join Date: Oct 2007 Location: Danger Zone	Take off the motor plate, take out the motor. Memorize how the wires are routed. Look inside the pistol grip. Then connect the grip to the mechbox. __________________ Airsoft, where nothing is hurt but feelings.

January 6th, 2012, 12:38	#7
ShadowNet Trader rating Join Date: Mar 2008	the Umarex HK416 is a VFC, so takedown is the same as a VFC M4. __________________

January 6th, 2012, 12:45	#8
Xtrykr Trader rating Join Date: Jul 2011 Location: Winnipeg	Danke - Awesome, got it, thanks man! +1 rep. Shadownet - You're right!

Umarex HK416 Takedown?

Airsoft Guns Discussion