Connectors: xt60 vs deans

krap101 · November 26th, 2011, 22:23

Hey guys,

I got some new batteries from hobbyking, and I'm wondering whether I should switch the batteries to deans or the gun to xt60? Sure deans is more common, but aside from that, which one is better?

L473ncy · November 26th, 2011, 23:46

XT60 for sure. Easy to solder and unlike deans the solder joint doesn't break as easily.

I personally don't like deans (and although they're better than Tamiyas.... it's considered stone age technology in the RC world) and I'm planning on switching to Trx, EC3's or XT60's for my next project gun.

ruinz00 · November 27th, 2011, 00:49

I switched to deans because all the kids were doing it. I really care much for them. Soldering a wire to a flat surface is annoying. I haven't switched to XT60's yet because I already switched part of my team over. I personally will switch all my own guns to something else.
I think you can get legit XT60's for cheaper than deans. Its been a while since I looked.

XZIVR · November 27th, 2011, 01:27

If you know what you're doing deans plugs are fine to solder to. I had to do it at work all the time when I worked at a hobby shop, so I got good quick.

I don't use the xt60 connectors simply because nobody else does, and I have around 3 dozen lipos, so it would cost a LOT to do.

If you want bullet connector style plugs, you could also look into EC3.

cbourdeau · November 27th, 2011, 21:48

Quote:

Originally Posted by XZIVR

If you want bullet connector style plugs, you could also look into EC3.

I was using ec3 connectors, but I found them a bit too big...I went to deans style connectors with the ribs on them that they sell at hobbyking and I like them. They're 100% compatible with regular deans.

By not being flat like deans, they fixed the major complaint I had about deans which was taking them apart, my fingers would always slip...

MaciekA · November 28th, 2011, 00:23

I have also been looking at XT60 since I'm ordering from Hobbyking a lot these days and their prices are so crazy low that you can actually begin to care about little details like connector ergonomics rather than just simply getting by. I strongly dislike soldering Deans and anything that would make it easier would be a huge plus.

I've read a few reviews of XT60 vs. Deans on RC sites, and people seem to really like XT60 for ergonomic factors as well as soldering (as mentioned above). I like the idea that I could load up on these on the cheap from hobbyking and know I have the "legit" ones whereas with Deans it's kind of a tossup... even when it isn't.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

November 26th, 2011, 22:23	#1
krap101 Trader rating Join Date: Jun 2007 Location: Roscoe, IL USA	Connectors: xt60 vs deans Hey guys, I got some new batteries from hobbyking, and I'm wondering whether I should switch the batteries to deans or the gun to xt60? Sure deans is more common, but aside from that, which one is better? __________________ AIRSOFT PRECISION DYNAMICS - Augmenting Reality

November 26th, 2011, 23:46	#2
L473ncy Trader rating Join Date: Oct 2004 Location: 11-30-24-1W5	XT60 for sure. Easy to solder and unlike deans the solder joint doesn't break as easily. I personally don't like deans (and although they're better than Tamiyas.... it's considered stone age technology in the RC world) and I'm planning on switching to Trx, EC3's or XT60's for my next project gun. __________________ ಠ_ಠLess QQ more Pew Pew READY TO >> RACE Last edited by L473ncy; November 26th, 2011 at 23:48..

November 27th, 2011, 00:49	#3
ruinz00 Trader rating Join Date: Apr 2010 Location: Regina, Sask	I switched to deans because all the kids were doing it. I really care much for them. Soldering a wire to a flat surface is annoying. I haven't switched to XT60's yet because I already switched part of my team over. I personally will switch all my own guns to something else. I think you can get legit XT60's for cheaper than deans. Its been a while since I looked.

November 27th, 2011, 01:27	#4
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	If you know what you're doing deans plugs are fine to solder to. I had to do it at work all the time when I worked at a hobby shop, so I got good quick. I don't use the xt60 connectors simply because nobody else does, and I have around 3 dozen lipos, so it would cost a LOT to do. If you want bullet connector style plugs, you could also look into EC3.

November 28th, 2011, 00:23	#6
MaciekA Trader rating Join Date: Jun 2011 Location: Portland, Oregon, USA	I have also been looking at XT60 since I'm ordering from Hobbyking a lot these days and their prices are so crazy low that you can actually begin to care about little details like connector ergonomics rather than just simply getting by. I strongly dislike soldering Deans and anything that would make it easier would be a huge plus. I've read a few reviews of XT60 vs. Deans on RC sites, and people seem to really like XT60 for ergonomic factors as well as soldering (as mentioned above). I like the idea that I could load up on these on the cheap from hobbyking and know I have the "legit" ones whereas with Deans it's kind of a tossup... even when it isn't.

Connectors: xt60 vs deans

Airsoft Guns Discussion