Motor Adjustment Screw Plate

Corey Darling · November 28th, 2006, 19:03

Hello

I believe i've lost the Adjustment Plate for the Motor in my TM MP5 RAS, didnt realize it existed when i first took the gun apart :S

From what I can tell, the part number is MP43. I've made a round plate out of some metal i had lying around (fits perfectly above the set screw, but its completely flat. Not sure if the actual plate has some special shape to it or not.

I havent been able to find a replacement plate online, just curious if someone knows where i can find one, or if the one i made will do okay?

Thanks

Corey

yanhchan · November 28th, 2006, 19:16

Thumb tac...take the pin part off and drill the hole!

Mantelope · November 28th, 2006, 19:20

Yeah, it's just a flat disc. Yours will probably work just fine.

CDN_Stalker · November 28th, 2006, 21:54

Ditto.

vondnik · November 28th, 2006, 22:03

3 inch framing mail head is a good replacement or a trimmed penny also works

Corey Darling · November 29th, 2006, 02:53

Great, thanks everyone, those suggestions would have saved me alot of time cutting out a round disk lol

Corey

CDN_Stalker · November 29th, 2006, 09:59

Once you have a disk that fits properly, use a bit of Krazy Glue on the base of the motor to hold the disk in place. Works great, and if you ever need to replace the motor, it pops off easily if you want it to.

hutch1970 · January 15th, 2007, 19:07

Forget the crazy glue.Any hard flat piece of metal, the correct circular shape, works great. Put a dab of lithium grease on it, then put it on your motor base plate under the grub screw.Re-affix, thenyour done. P.S.- slack the grub screw off before you do this.Hope this helps.

CDN_Stalker · January 15th, 2007, 19:26

Quote:

Originally Posted by hutch1970

Forget the crazy glue.Any hard flat piece of metal, the correct circular shape, works great. Put a dab of lithium grease on it, then put it on your motor base plate under the grub screw.Re-affix, thenyour done. P.S.- slack the grub screw off before you do this.Hope this helps.

Nah, I used to use the lithium grease to hold it in place, but it only lasts so long. Instant glue is the best, never have to worry about wearing it out (besides, if you are troubleshooting a bugger of an AEG and have to open it up and put it back together a few times) as far as stickiness goes, and you get to avoid the damned "Shit! I dropped the disk, where did it go?!?!" and you search around the bench and floor for 20-30mins, then realize the disk fell of and stuck to the side of the motor. Gluing it avoids a lot of hassles, and it only comes off when you want it to come off.

Renegade) · January 15th, 2007, 19:38

I totaly second everything Stalker just said, that damn plate is a major pain in the ass! Krazy glue to the bottom of the motor solves all...

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

November 28th, 2006, 19:03	#1
Corey Darling Trader rating Join Date: Mar 2005	Motor Adjustment Screw Plate Hello I believe i've lost the Adjustment Plate for the Motor in my TM MP5 RAS, didnt realize it existed when i first took the gun apart :S From what I can tell, the part number is MP43. I've made a round plate out of some metal i had lying around (fits perfectly above the set screw, but its completely flat. Not sure if the actual plate has some special shape to it or not. I havent been able to find a replacement plate online, just curious if someone knows where i can find one, or if the one i made will do okay? Thanks Corey

November 28th, 2006, 19:16	#2
yanhchan Trader rating Join Date: Jun 2005 Location: Scarborough/Richmond Hill ON	Thumb tac...take the pin part off and drill the hole! __________________ YANHCHAN'S AIRSMITHING: AEG repair/Tune up/Upgrades V2/V3 mechboxes, rewiring/reconnecting. Ask not what your country can do for you; ask what you can do for your country ~John F. Kennedy

November 28th, 2006, 19:20	#3
Mantelope Scotty aka harleyb Trader rating Join Date: Mar 2004 Location: Toronto, Ontario	Yeah, it's just a flat disc. Yours will probably work just fine. __________________

November 28th, 2006, 21:54	#4
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Ditto. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

November 28th, 2006, 22:03	#5
vondnik Ban-Fu Sifu Trader rating Join Date: Nov 2002 Location: Socialist republic of Kebekistan	3 inch framing mail head is a good replacement or a trimmed penny also works __________________ Vondnik, team Bad Karma, PQAC Murphy's second rule: Nothing is impossible for the man who does not have to do it himself.

November 29th, 2006, 02:53	#6
Corey Darling Trader rating Join Date: Mar 2005	Great, thanks everyone, those suggestions would have saved me alot of time cutting out a round disk lol Corey

November 29th, 2006, 09:59	#7
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Once you have a disk that fits properly, use a bit of Krazy Glue on the base of the motor to hold the disk in place. Works great, and if you ever need to replace the motor, it pops off easily if you want it to. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

January 15th, 2007, 19:07	#8
hutch1970 Trader rating Join Date: Jan 2007 Location: Texas, USA	Forget the crazy glue.Any hard flat piece of metal, the correct circular shape, works great. Put a dab of lithium grease on it, then put it on your motor base plate under the grub screw.Re-affix, thenyour done. P.S.- slack the grub screw off before you do this.Hope this helps.

January 15th, 2007, 19:38	#10
Renegade) A Total Bastard Trader rating Join Date: Apr 2006 Location: Tottenham, Ontario	I totaly second everything Stalker just said, that damn plate is a major pain in the ass! Krazy glue to the bottom of the motor solves all... __________________ W1-5

Motor Adjustment Screw Plate

Doctor's Corner