Dust cover for Madbull MUR upper receiver.

HKGhost · September 18th, 2010, 22:51

Hey guys, I'm need some help in finding a dust cover that could fit onto Madbull's MUR. I've tried a G&P, JG, CA and none fit. All where too small or didn't even come close to fitting. CA was wide enough but couldn't latch close. Anyone know which dust cover or brand that would fit? Thanks.

And yes I've checked Madbull's website and browsed the interweb with no luck.

Styrak · September 18th, 2010, 22:56

Why don't you reverse it so it's sprung closed, no open?

HKGhost · September 18th, 2010, 23:02

well the problem with the covers that I've tested is, they are all too small and leaving a 1-2cm gap at the top. the g&p one is way too small that even the width leaves a 2cm gap. Looks really funny with a tiny cover.

KrashRider · June 22nd, 2012, 16:36

Same here, anyone have an answer?

The KA is too short as well, gap along the top.

Kwokwai · June 22nd, 2012, 16:44

I had the same issue with a VFC Hk416 AEG body. Ended up getting a JG dustcover that just fit after going through four other ones that didn't.

KrashRider · June 22nd, 2012, 21:03

This websites states only CA dust cover - the only reference to dust cover to be used on this upper that I have seen.

http://jagprecision.com/store/index....cc821765f1tlk6

Says CA charging handle but I have a KA and it works fine.

KrashRider · June 26th, 2012, 09:08

Update: Mod the hinge on the dust cover.

Unroll the dust cover hinge a little the using a spare hinge pin. Hammer the hinge back around the pin. I was able to get mine to line up a little better this way. However it still will not latch so it solves the look but does not restore function.

dutch13 · July 4th, 2012, 23:09

I have the noveske upper from madbull for the two pin ca body. I used the dust cover from the old upper and it seemed to work fine, no gaps, butit doesn't want to latch so the spring is reversed like mentioned above.

KrashRider · August 9th, 2012, 01:59

Right from the lips of MadBull - The Echo 1 M4 Dust cover.

To get a working dust cover takes a little work. I used the MadBull charging handle with a King Arms handle arm. The problem is with the King Arms handle arm stops closing of the body since the hump on the top of the arm gets in the way. Trim off the hump flush with the top (ungroved side) of the arm. The next part is to trim a little off the dust cover release. The King Arms one is to big and too thick. So mod the dust cover release little by little until it doesn't push on the gear box or hop-up but still has enough to push the dust cover release pin.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

September 18th, 2010, 22:51	#1
HKGhost Trader rating Join Date: Nov 2009 Location: Mississauga, ON	Dust cover for Madbull MUR upper receiver. Hey guys, I'm need some help in finding a dust cover that could fit onto Madbull's MUR. I've tried a G&P, JG, CA and none fit. All where too small or didn't even come close to fitting. CA was wide enough but couldn't latch close. Anyone know which dust cover or brand that would fit? Thanks. And yes I've checked Madbull's website and browsed the interweb with no luck. __________________ Please email me as I'm not on ASC too often. Custom Build \| Upgrades \| Repairs \| Maintenance Contact: ghostgunwork@gmail.com / Private Message Last edited by HKGhost; September 23rd, 2010 at 22:31..

September 18th, 2010, 22:56	#2
Styrak Trader rating Join Date: Jan 2007 Location: Saskatoon, SK	Why don't you reverse it so it's sprung closed, no open? __________________ Airsoft Sales and Repair/Upgrade Services

September 18th, 2010, 23:02	#3
HKGhost Trader rating Join Date: Nov 2009 Location: Mississauga, ON	well the problem with the covers that I've tested is, they are all too small and leaving a 1-2cm gap at the top. the g&p one is way too small that even the width leaves a 2cm gap. Looks really funny with a tiny cover. __________________ Please email me as I'm not on ASC too often. Custom Build \| Upgrades \| Repairs \| Maintenance Contact: ghostgunwork@gmail.com / Private Message

June 22nd, 2012, 16:36	#4
KrashRider Trader rating Join Date: May 2011 Location: Airdrie	Same here, anyone have an answer? The KA is too short as well, gap along the top. Last edited by KrashRider; June 22nd, 2012 at 19:22..

June 22nd, 2012, 16:44	#5
Kwokwai Trader rating Join Date: Dec 2001 Location: Mississauga, ON	I had the same issue with a VFC Hk416 AEG body. Ended up getting a JG dustcover that just fit after going through four other ones that didn't.

June 22nd, 2012, 21:03	#6
KrashRider Trader rating Join Date: May 2011 Location: Airdrie	This websites states only CA dust cover - the only reference to dust cover to be used on this upper that I have seen. http://jagprecision.com/store/index....cc821765f1tlk6 Says CA charging handle but I have a KA and it works fine.

June 26th, 2012, 09:08	#7
KrashRider Trader rating Join Date: May 2011 Location: Airdrie	Update: Mod the hinge on the dust cover. Unroll the dust cover hinge a little the using a spare hinge pin. Hammer the hinge back around the pin. I was able to get mine to line up a little better this way. However it still will not latch so it solves the look but does not restore function.

July 4th, 2012, 23:09	#8
dutch13 Trader rating Join Date: Jul 2006 Location: Manitoba	I have the noveske upper from madbull for the two pin ca body. I used the dust cover from the old upper and it seemed to work fine, no gaps, butit doesn't want to latch so the spring is reversed like mentioned above.

August 9th, 2012, 01:59	#9
KrashRider Trader rating Join Date: May 2011 Location: Airdrie	Right from the lips of MadBull - The Echo 1 M4 Dust cover. To get a working dust cover takes a little work. I used the MadBull charging handle with a King Arms handle arm. The problem is with the King Arms handle arm stops closing of the body since the hump on the top of the arm gets in the way. Trim off the hump flush with the top (ungroved side) of the arm. The next part is to trim a little off the dust cover release. The King Arms one is to big and too thick. So mod the dust cover release little by little until it doesn't push on the gear box or hop-up but still has enough to push the dust cover release pin.

Dust cover for Madbull MUR upper receiver.

Accessories Discussion