KWA Glock 18c Problem

Riceboy43 · July 16th, 2011, 02:20

Ok Everytime I put Bb's in the mag then put it in the gun then cock it back and press the slide release the BB doesn't load inside the chamber at all. It stays stuck in the slide and i always have to disassemble the gun to take the bb out.Some times I could just take out the mag and wobble it alittle and the bb will just fall out.

So basically the BB won't load in the chamber at all.

Any suggestion whats wrong with it?

the_hellspawn · July 16th, 2011, 02:41

Maybe you should've posted this on the "Doctor's Corner" section. Hope you'll find an answer to your question.

weaky · July 16th, 2011, 08:17

could i dont know be BROKEN

surebet · July 16th, 2011, 11:07

Yeah, but that doesn't mean it can't be fixed.

XZIVR · July 16th, 2011, 11:39

Sounds like the little arm under the nozzle is broken. That's what is supposed to push the bb out of the mag and into the chamber.

Riceboy43 · July 16th, 2011, 14:24

So where can I buy a new loading nozzle? Because I checked a ton of websites and they were all out of stock

XZIVR · July 16th, 2011, 15:28

Did you have a look and figure out that was indeed the problem?

surebet · July 16th, 2011, 15:56

Check part 22 for damage. If I'm not mistaken, KSC Glocks 17 and 18c share the same part 22, so looking for a Glock 17 loading nuzzle might be easier.

http://unconventional-airsoft.com/gf...kpartslist.gif

Riceboy43 · July 16th, 2011, 16:23

Yes I checked it and it seems like a small part of it was chipped off in front of it

weaky · July 16th, 2011, 17:33

sʎnƃ ıɥ

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

July 16th, 2011, 02:20	#1
Riceboy43 Trader rating Join Date: Jun 2011 Location: California	KWA Glock 18c Problem Ok Everytime I put Bb's in the mag then put it in the gun then cock it back and press the slide release the BB doesn't load inside the chamber at all. It stays stuck in the slide and i always have to disassemble the gun to take the bb out.Some times I could just take out the mag and wobble it alittle and the bb will just fall out. So basically the BB won't load in the chamber at all. Any suggestion whats wrong with it? Last edited by Riceboy43; July 16th, 2011 at 02:59..

July 16th, 2011, 02:41	#2
the_hellspawn Trader rating Join Date: Jun 2009 Location: Rimouski, Qc	Maybe you should've posted this on the "Doctor's Corner" section. Hope you'll find an answer to your question. __________________ Airsoft guns: ICS M4 R.I.S.,TM VSR-10 Pro, CA P90, HFC M9, KWA M11A1

July 16th, 2011, 08:17	#3
weaky Trader rating Join Date: Jul 2011 Location: stephenville nl	could i dont know be BROKEN

July 16th, 2011, 11:07	#4
surebet Vicious MSPaint Wizard Trader rating Join Date: Aug 2004 Location: Longueuil, Quebec	Yeah, but that doesn't mean it can't be fixed.

July 16th, 2011, 11:39	#5
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	Sounds like the little arm under the nozzle is broken. That's what is supposed to push the bb out of the mag and into the chamber.

July 16th, 2011, 14:24	#6
Riceboy43 Trader rating Join Date: Jun 2011 Location: California	So where can I buy a new loading nozzle? Because I checked a ton of websites and they were all out of stock

July 16th, 2011, 15:28	#7
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	Did you have a look and figure out that was indeed the problem?

July 16th, 2011, 15:56	#8
surebet Vicious MSPaint Wizard Trader rating Join Date: Aug 2004 Location: Longueuil, Quebec	Check part 22 for damage. If I'm not mistaken, KSC Glocks 17 and 18c share the same part 22, so looking for a Glock 17 loading nuzzle might be easier. http://unconventional-airsoft.com/gf...kpartslist.gif

July 16th, 2011, 16:23	#9
Riceboy43 Trader rating Join Date: Jun 2011 Location: California	Yes I checked it and it seems like a small part of it was chipped off in front of it

July 16th, 2011, 17:33	#10
weaky Trader rating Join Date: Jul 2011 Location: stephenville nl	sʎnƃ ıɥ

KWA Glock 18c Problem

Airsoft Guns Discussion