[WE] G39C - H&K G36C for normal people

[Ninja_En_Short]

Remove the screws on bolt carrier and pin at the end of bolt carrier to disassemble. It's easy but the pin might a bit of a pain to get out.

[icemann]

^thanks!

[teriases]

Is there any way to tell if the mag is leaking besides listening to the hiss?

My OEM mag was a leak, it was replaced by the retailer with another one. But after testing it at home, and charging it to full again, I listened to the gas charging nozzle and still hear a very light hiss(guess didn't hear it before maybe it as noisy before where is was at).

Any other know if this is normal if the mag is full of gas? Does it stop after extra pressure is released...?(this is my guess)

Never had this issue with my GBB pistol mags maybe they're different...

Also, where did u order the sticker for HK trades? I like one too

[Ninja_En_Short]

Fill a bucket with water, put some gaz in the mag, remove plastic casing to see where the leak is and put into the bucket.

I always redo the seal on these thing, WE earned my award of worst design ever made.

[icemann]

^do you just oil the seal with silicon oil???

[Ninja_En_Short]

Noooo. And I'm not going to answer only 3 pages after the review, read it you'll see how to fix it.

[hattrick]

New to me, and I've owned the thing for 2 weeks now.


As seen around 2:40 here YouTube - WE　G39C(36C)GBB　134AãÂ�§ãÂ�®ä½ œå‹•ãƒâ€*スト

The charging handle can be locked to either side to be used as a "forward assist"

-alex

[Ninja_En_Short]

Like the real steel

But don't use it I made a few try on both side I doubt it is really sturdy enough to be used consistently.
Also on the review by the way.

[snipersyntagmatik]

speaking about the charging handle - this component should really be made of steel than plastic. mine broke off even after normal use, but i'm not surprised as this is a design flaw more so on the component material given how much stress this little handle goes thru.

i hope a metal upgrade gets released soon.

[Ninja_En_Short]

Steel no, heresy like a FAMAS full metal kit (it exists). Real one is plastic, it ought to be plastic here !
But a higher grade plastic would be nice.

[snipersyntagmatik]

Originally Posted by Ninja_En_Short

Steel no, heresy like a FAMAS full metal kit (it exists). Real one is plastic, it ought to be plastic here !
But a higher grade plastic would be nice.

take apart your charging handle. it's quite weak ... there is no way the handle will NOT break in time. it should be steel. these are not real firearms.

[Brian McIlmoyle]

Originally Posted by snipersyntagmatik

take apart your charging handle. it's quite weak ... there is no way the handle will NOT break in time. it should be steel. these are not real firearms.

So plastic is good enough for a real firearm but not good enough for an airsoft gun?

I Have seen no issue with the cocking handle.. one would have no mishandle it roughly to break it.

[snipersyntagmatik]

Originally Posted by Brian McIlmoyle

So plastic is good enough for a real firearm but not good enough for an airsoft gun?

I Have seen no issue with the cocking handle.. one would have no mishandle it roughly to break it.

I don't agree. I have never seen nor handled a real H&K G36c. That being said, I cannot attest to how the material would compare to a WE G39c airsoft rifle. I am pretty sure they're NOT on par material-wise. Don't get me wrong, I love this gun and I believe it will do quite well as staple GBBR platform. But I assure you, no mishandling on my part - the handle should be made of a material more robust than what it is made of right now.

[Brian McIlmoyle]

Originally Posted by snipersyntagmatik

I don't agree. I have never seen nor handled a real H&K G36c. That being said, I cannot attest to how the material would compare to a WE G39c airsoft rifle. I am pretty sure they're NOT on par material-wise. Don't get me wrong, I love this gun and I believe it will do quite well as staple GBBR platform. But I assure you, no mishandling on my part - the handle should be made of a material more robust than what it is made of right now.

Real one is glass fiber composite with a metal insert... , I'd agree I wish it was made of sterner stuff but then it would cost more..

in the design and manufacture of these things I expect there are a lot of Cost benefit trade-offs to get a good robust product to market at a price that people will pay.

I really like the HK G36K WE model... of all the WE's I have ( and there are currently 12 on my gun rack) I find the G36K the most fun to shoot

[Ninja_En_Short]

And there's too much C anyway !