This is the KJ 10/22 thread

[T-Hell]

Yea the Version 1 is hard to find.

they are highly sought after because the version 2 does not have a threaded outer barrel basically that is the only difference that and the stock short mag...

Just keep your eye on the major sights. there are no issues getting this gun in from the USA

[T-Hell]

Airsplat has them in stock
http://www.airsplat.com/Items/GR-KJW-KC02-B.htm

249.00

[BennyBoy]

Got another question for ya gents, read a lot but may of missed this..
What bore are you guys using? 6.01 or 6.03 or something else?

[T-Hell]

6.01 510mm RATech inner...

basically your choices are
6.01 380mm RATech
6.01 510mm RATech
6.01 510mm Falcon

if you are getting a 510mm then I personally like the RATech BUT the falcon inner barrel is just as nice and if you get the Kit then you get the Falcon Hopup Rubber + 510mm 6.01 and the barrel extension (which you will want) as a kit for like $80.00

[BennyBoy]

so 6.01 are the way to go...I did a 6.03 but it was rather short
gah why am I doing this, I don't even own this gun hahaha just ordering for another rifle and thought I'd throw these in so save on shipping for later time

Edit: The falcon one comes with inner, outer extension and hopup rubber...

[R700]

used my 10/22 v2 today. temp was 12 celsius. I have the ra tech 380 tbb and the ra tech hop up. The hop up is installed correctly.

I was using .4 Action Army bbs and the hop up was not doing anything to them. Fully off and on and the bbs would travel 20m and drop off.

I used the .3s and the hop up adjustments were working and i could get out to 75 m easy.

Why would the ra tech hop up not work on the .4s. I know its not a faulty part thing cuz the .3s hopped perfectly.

Has anybody experienced this. I was using propane and the long mags.

[R700]

fixed my problem. The silicone and propane mixture was a little steep on the silicon side. I guess too much got on the hop up and wasnt allowing it tow work. I took the gbbr apart. Cleaned the barrel, the hop up and chamber and used green gas only and the .4 bbs were bucking out to 75 m nicely.

Moral of the lesson, don't overuse silicon.

[ahchien]

Originally Posted by R700

I just received my 10/22 version 2. In advance i bought the RA TECH 380mm and the RA TECH hop up.

After disassembling the barrel. I noticed that mine has a inner sleeve inside the outer barrel that looks like a inner barrel extension for the stock barrel. I cannot install the 380mm cuz this "built in" inner barrel extension prevents the 380mm from going in. Any idea on how to remove that inner extension so the 380 tbb fits.

Also, this little metal shim fell off the lower receiver. It is about 1cm long and 3 mm wide. I have no idea but when i flipped over the lower, it fell from somewhere? any ideas of were it goes? I think it fell off near the barrel nut but it came from the magwell side underneath the receiver...i think. This is approximately the size.

The shim is used for the connector with the two allen key screws that holds the outer barrel to the trigger and bolt assembly.

I will tak a picture when i disassemble my

Sent from my SGH-I747M using Tapatalk 2

[ahchien]

Got a question for you guys. About how many rounds can 1 co2 cartridge get ?

[T-Hell]

you will get about 2 perhaps 2.5 mags worth.. BUT this depends how fast you shoot. faster shooting means colder mag = decreased pressure

Heat will play into it too...

in my tests with +22 degrees I have gotten 2 / 2.5 mags

[ahchien]

Thanks

Sent from my SGH-I747M using Tapatalk 2

[ahchien]

Where the metal shim goes


Sent from my SGH-I747M using Tapatalk 2

[R. Jones]

Anyone put a grenade launcher (M-203) on their KC-02? If yes, what did you get and how does it mount? Pics?

Thanks

[T-Hell]

There are rails on each side of the gun...

Hmmm 203 on a gun that gets 200+ feet with accuracy.... hmmm counter productive I would just drop to a secondary myself....

[Strelok]

Anyone know a site for buying aftermarket stocks for a 1022? Wanting to locate a Hogue Overmold stock for it, or something similar.