Wetti Awss Scar

[KEVORKIAN]

I must say these Co2 mags kick like a son-of-a-gun!
Getting them to fit the PMags correctly requires the use of a dremel...fits like a glove!

[KEVORKIAN]

I decided to do some testing with my WE SCAR this evening since the Leafs game is boring...they're actually winning!

I finally installed my RA-Tech NPAS with the LAT piston head (installed on stock nozzle guide rod).
Shots were very consistent, and within +/-4 FPS of each other.
The RA-Tech NPAS dialed in nicely but it's a little hard to adjust with the tool and it requires you to hold back the valve disc with a small flathead screwdriver.

RA-Tech NPAS:


LAT piston head:



NPAS installation & testing by RA-Tech:
YouTube- RA TECH WE NPAS

I also tried the LAT SS mag valve and it did increase velocity by +15-20 FPS.
Where it failed was when it was tested on full auto, it dumped a lot a gas and the ROF actually seemed to slow down compared to the stock valve.
This may be a part that someone might consider using if building a sniper platform, so long as it's used in semi-auto only!

[Zulu]

Ok guys, I recently installed the TSC NPAS which broke after 10 rds. I ended up taking the adjustment wheel from the tsc and used it on the stock guide rod. Avoid it like the plague for now. I am awaiting a response from them but have heard nothing yet.

[m102404]

What part of the TCS setup broke? The nozzle? The valve? The rod/piston? The Adjustment wheel?

They're nozzles are Stainless Steel aren't they? Did it crumple with a misfeed?

[KEVORKIAN]

Originally Posted by Zulu

Ok guys, I recently installed the TSC NPAS which broke after 10 rds. I ended up taking the adjustment wheel from the tsc and used it on the stock guide rod. Avoid it like the plague for now. I am awaiting a response from them but have heard nothing yet.

Are you referring to this part:

[Zulu]

Originally Posted by m102404

What part of the TCS setup broke? The nozzle? The valve? The rod/piston? The Adjustment wheel?

They're nozzles are Stainless Steel aren't they? Did it crumple with a misfeed?

The pic kevorkian just put up is it. On the v1's the end piece of the guide rod (opposite the adjustment wheel) is basically a round threaded nut that appears to be held in place by a very craptastic weld. From further research this issue has been corrected in the new version. Tokyo model company did not list the version and I got stuck with a v1. Make sure the one you order is ts-13B. The guide rod does not come with a new nozzle.


I also just got in the VFC EGLM and it's very nice. WGC had them for 126.00 (155.00 shipped to VA). Very well constructed and half the price of the Ares.

Now if I can just figure out why I keep chopping bb's.....

[Shirley]

Originally Posted by Zulu

The pic kevorkian just put up is it. On the v1's the end piece of the guide rod (opposite the adjustment wheel) is basically a round threaded nut that appears to be held in place by a very craptastic weld. From further research this issue has been corrected in the new version. Tokyo model company did not list the version and I got stuck with a v1. Make sure the one you order is ts-13B. The guide rod does not come with a new nozzle.


I also just got in the VFC EGLM and it's very nice. WGC had them for 126.00 (155.00 shipped to VA). Very well constructed and half the price of the Ares.

Now if I can just figure out why I keep chopping bb's.....

You modded a PMAG too?
What bb's are you using? First V1's hop-ups are shit.. lol

[Zulu]

Originally Posted by Mr.Hitman

You modded a PMAG too?
What bb's are you using? First V1's hop-ups are shit.. lol

Hitman,
So far I have modded 4 WE to pmag and assisted my boss as he's modded some for his PTW. (PTW mags don't require as much sanding )

As far as ammo I've tried TSD bio & non bio, KSC and some Bioval.
The gun itself is a gen III so no gen I hop-up.

As soon as I can dial in the gun we will probably start carrying them. (We as in my employer www.airsoftcqb.com)

[Zulu]

Got the RA Tech NPAS and it is so much better than the TSC fiasco. +1 to the Folks at RA !

[sortie39]

whats the name of the grid pad?where did u get that??

[KEVORKIAN]

Originally Posted by sortie39

whats the name of the grid pad?where did u get that??

It's made by OLFA (36" x 24") and I purchased it from an arts & craft store here in Winnipeg called " Michaels' "
LINK: http://www.michaels.com/art/online/s...0&y=0&as_fid=1

[BIG]

Hey guys,

What do you think about that color patern?

I bought a used tan SCAR but I wanted a black one. Now I don't want to paint it all black because I don't want to loose the markings.

[Thenooblord]

Originally Posted by BIG

Hey guys,

What do you think about that color patern?

I bought a used tan SCAR but I wanted a black one. Now I don't want to paint it all black because I don't want to loose the markings.

but...but....but.... tan is so much sexier than black....

[KEVORKIAN]

Originally Posted by BIG

Hey guys,

What do you think about that color pattern?

I like it!
I just might have to do that to mine!

[BIG]

hey! If you have a black one, we could switch parts!!!