|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
September 27th, 2009, 16:17 | #1 |
A minor, using dad's ID
|
Well VSR-10 Barrel
Hey guys, just wondering what barrel i should get?
Im going full PDI bore up, but the TM barrel lengths are different than the Well. And I've heard a silencer adapter doesnt work, any ideas? |
September 27th, 2009, 16:40 | #2 |
If you're going bore-up go above 550mm otherwise all that additional air will be lost.
|
|
September 27th, 2009, 18:53 | #3 |
A minor, using dad's ID
|
Yes, the Well Barrel is 510mm, so im thinking i will try to add my silencer to it. Has anyone heard if the PDI adapters work? Last i heard was that they didn't;might have to do a home made adapter.
|
September 27th, 2009, 20:57 | #4 |
the King Arms adapter does work.. (threads properly). However, you will have to remove the last 3 or 4 threads in order for it to fit flush.
And you probably want to wrap the threads with electrical tape for tight fit. |
|
September 27th, 2009, 21:17 | #5 |
A minor, using dad's ID
|
But i could also just get the 430mm, which is cheaper, and 80mm isn't That much to sacrifice.
|
September 27th, 2009, 21:18 | #6 |
ya thats a good idea, just get the 430mm. Much less headache.
|
|
September 27th, 2009, 21:19 | #7 |
A minor, using dad's ID
|
Then again, i want the most accuracy i can get. Oh the joy of upgrading
|
September 27th, 2009, 21:21 | #8 |
i'm running a 430mm 6.01 in mine... very accurate!
__________________
member of fire team NOM. my other regular forum: www.toyotanation.com / gen3,gen4 camry |
|
September 27th, 2009, 21:22 | #9 |
A minor, using dad's ID
|
Alright, 430mm it is!
|
September 27th, 2009, 21:55 | #10 |
Don't get bore-up for 430, stick to standard bore.
|
|
September 27th, 2009, 23:16 | #11 |
A minor, using dad's ID
|
So a Bore up setup, with normal TightBore?
|
September 27th, 2009, 23:22 | #12 |
so you are going for 510mm outerbarrel + 430mm inner barrel?
|
|
September 27th, 2009, 23:39 | #13 |
Bore-up refers to internals.. not the tightbore.
Bore-up is used when the stock cylinder can't push out enough air to make use of the extra length in a barrel... after 550mm, you'll see a slow decline in performance as the barrel gets longer and longer... This is where bore-up comes in. |
|
September 27th, 2009, 23:49 | #14 |
A minor, using dad's ID
|
Oh ok. So ill get full PDI bore up internals, and a 6.01 PDI tightbore, in 430mm length. Thanks for the help guys!
|
September 27th, 2009, 23:59 | #15 | ||
Quote:
no offence, but are you even reading what Amos is telling you?
__________________
Quote:
Chinese proverb
Last edited by theguy; September 28th, 2009 at 00:16.. |
|||
|
Bookmarks |
Thread Tools | |
|
|