TM Hi-Capa 4.3 Metal Slide + Barrel Installation?

Identity · August 7th, 2006, 17:41

Anyone know how to install a Metal Slide + Metal Barrel Upgrade for the Tokyo Marui HI-Capa 4.3?

I just ordered one from an ASC member and hopefully it arrives tomrrow.

I need some help installing it, unless someone can guide me through or show me some pictures on how to install it.

If anyone can help me let me know,

-Identity.

Ph0_Eat3r · August 7th, 2006, 20:05

when you pull down the hammer do u see a allen key type of screw in the midle below your sight if it does i think it should be the same as a 5.1 slide install

Autumn · August 7th, 2006, 20:37

It’s not too hard to figure out how to install the slide. Just go slow and make sure to check your manual frequently. It should have a pretty good diagram of the assembly. You may have some trouble removing the outer barrel though. It was a little confusing for me as I did not want to use force. You just have to bend the plastic a bit and the inner barrel and hop up should just pop out for you.

I tried to find some instructions or tutorials online, but I could not find any for the Hi-Capa, though you may have better luck then me.

Hope it goes well.

Identity · August 7th, 2006, 21:51

Great stuff, after trying to fix up my Hi-Capa which still has problems I kinda figure out how to disassemble it.

Identity · August 8th, 2006, 14:08

Alright I got the metal slide, I took off the allen screw on the back of the hammer on the slide, now I dont know where to continue. The whole part doesnt seem to move...

Jugglez · August 8th, 2006, 15:51

Use some force to bend the two sides of the plastic slide away from each other, while wiggling the block out. Careful a spring might come flying out. Might wanna put your paintball goggles on

Identity · August 8th, 2006, 16:07

Quote:

Originally Posted by Jugglez

Use some force to bend the two sides of the plastic slide away from each other, while wiggling the block out. Careful a spring might come flying out. Might wanna put your paintball goggles on

Hehe I got everything on, except for the metal barrel! It's so hard to put the barrel in with the hopup.. I still dont know how...

I left the plastic barrel on and tested the slide, the only thing is that the slidelock kinda gets stuck and you have to push the slide and wiggle it around for the slidelock to fit in.

If anyone knows how to put the metal barrel on let me know! :salute:

Thanks.

dead_aim · August 8th, 2006, 16:30

btw what brand did you get??

pm me...i live at shep and warden if you want i can give you some help....i have a creation on my 4.3 heavy bitch too..

Identity · August 8th, 2006, 16:46

Right on, however deadaim isnt available till like 9:15pm... Does anyone else here know how to fit the hopup + barrel on the gun?

hattrick · August 8th, 2006, 17:20

yeah, its a simple twist. Counter clockwise if i remember right...(i know it doesnt look like it was ever ment to be taken out!)

Identity · August 8th, 2006, 19:04

Quote:

Originally Posted by neir

yeah, its a simple twist. Counter clockwise if i remember right...(i know it doesnt look like it was ever ment to be taken out!)

Not the original one, Im trying to put in a new metal barrel.
Not take it out.

Identity · August 9th, 2006, 14:56

Anyone? Any suggestions?

dead_aim · August 10th, 2006, 02:51

i'll let you know wen i get a day off...if you still have a problem...

Identity · August 10th, 2006, 03:02

Quote:

Originally Posted by dead_aim

i'll let you know wen i get a day off...if you still have a problem...

Aw dude dead_aim sorry about not calling you... Keep forgetting and I think I'll put of the metal slide off for awhile untill I get my new sights for the metal slide. The front sight on the 4.3 was gluded on. So I do not know how to take it off...

stokes · August 10th, 2006, 03:12

If the front sight is metal. You can use alittle heat to melt the glue off. Done that plenty of times it works.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 7th, 2006, 17:41	#1
Identity Banned Trader rating Join Date: Aug 2003 Location: Markham, Toronto	TM Hi-Capa 4.3 Metal Slide + Barrel Installation? Anyone know how to install a Metal Slide + Metal Barrel Upgrade for the Tokyo Marui HI-Capa 4.3? I just ordered one from an ASC member and hopefully it arrives tomrrow. I need some help installing it, unless someone can guide me through or show me some pictures on how to install it. If anyone can help me let me know, -Identity.

August 8th, 2006, 15:51	#6
Jugglez Trader rating Join Date: Feb 2005 Location: Swimming in a pool of Xpresspost receipts.... Toronto - 400/401	Use some force to bend the two sides of the plastic slide away from each other, while wiggling the block out. Careful a spring might come flying out. Might wanna put your paintball goggles on __________________

August 8th, 2006, 16:30	#8
dead_aim Trader rating Join Date: Jul 2005 Location: scarborough	btw what brand did you get?? pm me...i live at shep and warden if you want i can give you some help....i have a creation on my 4.3 heavy bitch too.. __________________

August 7th, 2006, 20:05	#2
Ph0_Eat3r Trader rating Join Date: Oct 2005 Location: toronto	when you pull down the hammer do u see a allen key type of screw in the midle below your sight if it does i think it should be the same as a 5.1 slide install

August 7th, 2006, 20:37	#3
Autumn Trader rating Join Date: Jun 2006 Location: Coquitlam	It’s not too hard to figure out how to install the slide. Just go slow and make sure to check your manual frequently. It should have a pretty good diagram of the assembly. You may have some trouble removing the outer barrel though. It was a little confusing for me as I did not want to use force. You just have to bend the plastic a bit and the inner barrel and hop up should just pop out for you. I tried to find some instructions or tutorials online, but I could not find any for the Hi-Capa, though you may have better luck then me. Hope it goes well.

August 7th, 2006, 21:51	#4
Identity Banned Trader rating Join Date: Aug 2003 Location: Markham, Toronto	Great stuff, after trying to fix up my Hi-Capa which still has problems I kinda figure out how to disassemble it.

August 8th, 2006, 14:08	#5
Identity Banned Trader rating Join Date: Aug 2003 Location: Markham, Toronto	Alright I got the metal slide, I took off the allen screw on the back of the hammer on the slide, now I dont know where to continue. The whole part doesnt seem to move...

August 8th, 2006, 16:46	#9
Identity Banned Trader rating Join Date: Aug 2003 Location: Markham, Toronto	Right on, however deadaim isnt available till like 9:15pm... Does anyone else here know how to fit the hopup + barrel on the gun?

August 9th, 2006, 14:56	#12
Identity Banned Trader rating Join Date: Aug 2003 Location: Markham, Toronto	Anyone? Any suggestions?

August 10th, 2006, 02:51	#13
dead_aim Trader rating Join Date: Jul 2005 Location: scarborough	i'll let you know wen i get a day off...if you still have a problem... __________________

August 10th, 2006, 03:12	#15
stokes Trader rating Join Date: Dec 2005 Location: Toronto	If the front sight is metal. You can use alittle heat to melt the glue off. Done that plenty of times it works.

TM Hi-Capa 4.3 Metal Slide + Barrel Installation?

Doctor's Corner