One stick battery for buffer tube

[turok_t]

Hey guys, im looking for a NiMH or NiCD stick battery that i can fit in my G&P buffer tube. It can be 3.6V, 4.8V, or even higher, as long as I can shoot on semi auto. Im not really concerned if the ROF is sluggish since I know it is affected by voltage. Also, I dont really care about the MAH rating as long as it fits in my buffer tube. I know that I can go lipo, but i rather not take that route yet. I just want a working battery that can fit inside my buffer tube so that i can use my CTR stock over it. Anyone know where i can get/make such battery?

[coach]

get a 7.2v mini custom made at cheapbatterypacks.

you will need to get the 2/3A batteries. I had a 9.6v made to go in my king arms collapsible stock but 2 of the cells had to go in the small storage compartment where you can put 2 x cr123's and it had to be modified to allow the wires to go through.

if you can run off of 7.2V mini just go with that. see if you can fit 6 x 2/3A batteries in there. dimensions at cheapbatterypacks. also add a bit of length for wires, end pieces and solder.

[The Chad]

Here man, love these guys, very reliable.

http://torontoairsoft.com/product.php?id_product=447

[turok_t]

Originally Posted by LoveMyStubby

Here man, love these guys, very reliable.

http://torontoairsoft.com/product.php?id_product=447

If u read my post, I indicated NO li-po

Originally Posted by coachster

get a 7.2v mini custom made at cheapbatterypacks.

you will need to get the 2/3A batteries. I had a 9.6v made to go in my king arms collapsible stock but 2 of the cells had to go in the small storage compartment where you can put 2 x cr123's and it had to be modified to allow the wires to go through.

if you can run off of 7.2V mini just go with that. see if you can fit 6 x 2/3A batteries in there. dimensions at cheapbatterypacks. also add a bit of length for wires, end pieces and solder.

Well, I have a CTR stock over my buffer tube, so i can put max 5 x 2/3A with the stock fully extended, or 4 x 2/3A. There's no way I can put 6 inside though. Will 4 batteries (4.8V) be enough?? Would it be able to drive the motor?

[coach]

Originally Posted by turok_t

Will 4 batteries (4.8V) be enough?? Would it be able to drive the motor?

no

yes but not enough for the motor to drive the gears that push the spring

[The Chad]

Sorry man, didn't notice it was LiPo.......here is another:
http://torontoairsoft.com/product.php?id_product=387
I think any Mp5 battery stick would be good wouldn't it?

[turok_t]

Originally Posted by LoveMyStubby

Sorry man, didn't notice it was LiPo.......here is another:
http://torontoairsoft.com/product.php?id_product=387
I think any Mp5 battery stick would be good wouldn't it?

Thats way too long.. I can only fit 4, max 5 in mine..

[The Chad]

Ah, I got nothing then, sorry man.

[StrikeFreedom]

A 7.2V lipo should be fine on your internals. I've seen one that's an eraser-sized, about 500MAH.

[turok_t]

Originally Posted by StrikeFreedom

A 7.2V lipo should be fine on your internals. I've seen one that's an eraser-sized, about 500MAH.

How much is it? Where?

How much is a charger/discharger for Lipos?

[StrikeFreedom]

IIRC it was around $25, at a hobby shop near Woodbine/Hwy 7.

[Boyso]

Yeah but a charger is 100ish, and you need another kind of charger that I forgot how it's called, that is not cheap either.

[KND]

Originally Posted by turok_t

How much is it? Where?

How much is a charger/discharger for Lipos?

All you need is to PM me. I will give you a good deal of Lipo battery that will fit in your buffer tube and a high quality charger that won't turn your battery to explosive device and won't burn down your garage.

Since this one might probably the best deal, So if you don't PM me then you missed it. That's all

[turok_t]

Oh i PM'd you..

[turok_t]

Okay, I think im going to make one with Intellect 2/3A batteries. They are $2 each so I'll see what I can do.