L96 market research part 1- L96 Owners please vote

[FOX_111]

In despair, try the ink tube of a bic pen. I heard from good source that it's a good replacement for a hopup bucking.

[Master Blaster]

Originally Posted by FOX_111

In despair, try the ink tube of a bic pen. I heard from good source that it's a good replacement for a hopup bucking.

I'm not sure that would work at all!

[Kos-Mos]

Bucking is the little nub that goes outside the sleeve and that applies the pressure on it.

You might want to consider the PDI L96 hop-up chamber. 50$ and you can use AEG tightbores and rubbers.

You have to remove the receiver/barrel assembly.
Then remove all the cross screws.
Open the stock in half.
On the left section, just in front of the magwell, is a little plate held in place by two screws.
Under that is the lever and a spring. Fiddle with it until you find the right way. The follower of your magasine is pushing on a lever that is then pushing on that little lever. The spring it there to hold it closed when there is still bbs.

[Master Blaster]

Originally Posted by Kos-Mos

Bucking is the little nub that goes outside the sleeve and that applies the pressure on it.

You might want to consider the PDI L96 hop-up chamber. 50$ and you can use AEG tightbores and rubbers.

Do you have a photo of it....im still not sure what your talking about!

[Kos-Mos]

Here.

The sleeve is the larger tube-like part.
The bucking is the little nub.
These are for AEG, but the parts in your L96 should be similar.



And here is the PDI part I am talking about:

[Master Blaster]

Originally Posted by Kos-Mos

Here.

The sleeve is the larger tube-like part.
The bucking is the little nub.
These are for AEG, but the parts in your L96 should be similar.



And here is the PDI part I am talking about:

Ya, i have the hop-up chamber on order from PDI, but on the "Well", the "bucking" is not there. Its the sleeve/hop-up rubber that locks the BB in once the BB has been chambered. I put the gun back together without the sleeve (it got mangled) , and the BB's roll out of the barrel now.

[Kos-Mos]

You would need a sleeve for APS-2 Type 96.

But since you have that PDI chamber on the way, better just wait for it.

And you will need a new barrel too. You can't use your old one with that chamber.

[Master Blaster]

Originally Posted by Kos-Mos

You would need a sleeve for APS-2 Type 96.

But since you have that PDI chamber on the way, better just wait for it.

And you will need a new barrel too. You can't use your old one with that chamber.

Ya, i have a PDI barrel coming as well!

[FOX_111]

The bic ink tube work for AEGs. I never compared the size of both hopup rubber (bucking). But Vondnik once proposed it for my PDI hopup in my old M24.

[jimmycudo]

I tried to get the WELL but I couldn't and had to settle with the UTG, which isn't all too bad tbqh. Then again, I've never used the WELL so what do I know... haha

[Luujerr]

is there any way to replace parts of the original chamber without going to aeg barrels? or is there a hop-up chamber that uses the stock barrel?

[Treefingers]

You can use a file to make AEG-like grooves in the original barrel.

[wildcard]

Maruzen "Killer Studio" edition L96, and like Amos said "Go maruzen or go home"

[Soulfly]

I have a Maruzen Type96 myself..

What do you guys recommend for a barrel? 6.01, 6.03/6.04?

I'll be shooting SGM's.

Originally Posted by wildcard

Maruzen "Killer Studio" edition L96, and like Amos said "Go maruzen or go home"

Post up a pic!!

[wildcard]

Originally Posted by Soulfly

I have a Maruzen Type96 myself..

What do you guys recommend for a barrel? 6.01, 6.03/6.04?

I'll be shooting SGM's.


Post up a pic!!

Not at home right now I'm in in B.C, its exactly like any other black L96 with a few exterior cosmetic upgrades, mainly a thicker silencer type barrel sleeve and a Full PDI internal upgrade. shooting 443 with a .28 bbs got it almost 9 yrs ago gamed it once.
I got the PDI 6.03 Titanium but I don't think they make those no more only Stainless steel, Used the 6.01 but they jam in winter play