Case Foam

[Bob the Angry Potato]

Step 1 is finished. Went to Fabricville earlier and picked up the foam they had, it's perfect but only came in one colour.



Steps 2 and 3 will be cutting out the shapes, and painting the entire thing either very dark grey or black.

[TokyoSeven]

Depending on how deep your brief case is and how much work you have to work with on the inside, set it up like this.

http://www.casesbypelican.com/military/m9-5pack.htm

It wont display the guns as well, but its good for space saving, and if you cut it right you may even have room for additional magazine space.

A piece of foam 3.5 feet x 1.5 feet and 2 inches deep ran me about 20 bucks, its not cheap stuff though, very high quality foam.

The two pieces of quater inch deep foam of the same size only cost me 10.

[Bob the Angry Potato]

Originally Posted by TokyoSeven

Depending on how deep your brief case is and how much work you have to work with on the inside, set it up like this.

http://www.casesbypelican.com/military/m9-5pack.htm

It wont display the guns as well, but its good for space saving, and if you cut it right you may even have room for additional magazine space.

A piece of foam 3.5 feet x 1.5 feet and 2 inches deep ran me about 20 bucks, its not cheap stuff though, very high quality foam.

The two pieces of quater inch deep foam of the same size only cost me 10.

That's a great idea, but these briefcases are simply bog-standard leather ones, and I can't see any way for them to fit like that. I'm going to guess Matt491 has one of those too, there's recently been a sale of them ($19.99 at Bentley's), which is probably inspiring quite a few people to do this.

I can't picture either an M93R or a Desert Eagle (which, some of the biggest standard handguns out there, are ironically what we have) going into these at an angle.

[TokyoSeven]

I understand, large guns may not work so well, perhaps two cases would work better, 3 per case.

Also

Same idea as above, but cut the grooves at a 45 degree angle so they slant? It may look somewhat off though, just a passing thought.

[Rookie Ab]

In Calgary the place I went to is called Future Foam.They pre cut them to fit the pelican case I have.Get one for each gun .The sticker on the bag said it came from Norseman Foam Products Inc. Maybe there's stores across Canada ??They have the Grey & Black foam your looking for.

[matt491]

don't have the brief case yet, I'm looking for one that's deep and recessed on both the bottom and top part so I can have guns on both the bottom of the case and the lid of the case. 3 on each side. The slots wont work, unfortunately. =P But it's a neat idea.

P.S. http://www.casesbypelican.com/military/m9-36pack.htm JESUS CHRIST! How many Beretta's do you need!?

[dontask]

Originally Posted by matt491

P.S. http://www.casesbypelican.com/military/m9-36pack.htm JESUS CHRIST! How many Beretta's do you need!?

obviously never enough
that case is like the ultimate multi-holster

[TokyoSeven]

http://www.casesbypelican.com/military/m9-36pack.htm

Bah what a useless thing! I need one that holds 37.

[dodger_me]

is that designed for military to be taking guns on planes? because from what i remember you need to have the bolts or slides in a different containers for commercial

[TokyoSeven]

Im guessing it would probly be for military, although I could see it just as storage and transport for police as well. Perhaps, I dont know.

[JTF27]

Well my case is done in the same manner as Bob's but I'm thinking of getting another case for my future pistols and the other for my sights and so on.

[matt491]

Post up some photo's of the finished product!