src m4 help

dead_aim · March 9th, 2006, 01:10

i have a src m4a1 ris with a 9.6 crane stock...upgraded internals..

my problem is it stop working...the battery heated up and the pistol grip (motor)...smells too..any suggesttions??

Grim Fandango · March 9th, 2006, 01:12

motor is probably fried. the motor tends to do that with anything higher than 8.4v. Best bet is to try and find a TM motor and replace it.

mcguyver · March 9th, 2006, 01:22

Check the wiring in your carne stock as well. Sometimes it can rub and chafe, causing you to short-circuit your battery. This would cause the excessive heating of you battery. Your motor may really be toast as Grim says, or it might have that "new motor" smell, and it's your battery that's toast. At any rate, it doesn't hurt to look anyway.

dead_aim · March 9th, 2006, 02:46

rub and chafe..what do you mean by that?? sort dont get it

Cortexburn · March 9th, 2006, 02:49

He means the wire can rub against the box/stock..whatever, end result is the insulation on the wire is compromised and you get a short. I had it happen with my HK33 and my 3000mah battery was good for cooking eggs on. Check your wiring for cracks, cuts and splits.

dead_aim · March 9th, 2006, 17:32

well when my gunsmith installed my my metal body he did cut my crane stock wire to pull the gun apart...and then sodered the tip back...i guess that was the problem

Jar|-|ead · March 13th, 2006, 19:38

is your gunsmith by anychance 6mm??...

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

March 9th, 2006, 01:10	#1
dead_aim Trader rating Join Date: Jul 2005 Location: scarborough	src m4 help i have a src m4a1 ris with a 9.6 crane stock...upgraded internals.. my problem is it stop working...the battery heated up and the pistol grip (motor)...smells too..any suggesttions?? __________________

March 9th, 2006, 01:22	#3
mcguyver Trader rating Join Date: Aug 2005 Location: Northern Alberta	Check the wiring in your carne stock as well. Sometimes it can rub and chafe, causing you to short-circuit your battery. This would cause the excessive heating of you battery. Your motor may really be toast as Grim says, or it might have that "new motor" smell, and it's your battery that's toast. At any rate, it doesn't hurt to look anyway. __________________ Age verifier Northern Alberta Democracy is two wolves and a sheep discussing what's for dinner. Freedom is the wolves limping away while the sheep reloads. Never confuse freedom with democracy.

March 9th, 2006, 02:46	#4
dead_aim Trader rating Join Date: Jul 2005 Location: scarborough	rub and chafe..what do you mean by that?? sort dont get it __________________

March 9th, 2006, 01:12	#2
Grim Fandango Trader rating Join Date: Oct 2002 Location: Toronto, Ontario	motor is probably fried. the motor tends to do that with anything higher than 8.4v. Best bet is to try and find a TM motor and replace it.

March 9th, 2006, 02:49	#5
Cortexburn Miserable Bastard Trader rating Join Date: Nov 2000 Location: Red Deer, Alberta	He means the wire can rub against the box/stock..whatever, end result is the insulation on the wire is compromised and you get a short. I had it happen with my HK33 and my 3000mah battery was good for cooking eggs on. Check your wiring for cracks, cuts and splits. __________________ My Buy/Sell Rating. “We cannot defend freedom abroad by deserting it at home.” Thomas Jefferson I hate Ghillie suits. Socialism SUCKS www.unisevil.com

March 9th, 2006, 17:32	#6
dead_aim Trader rating Join Date: Jul 2005 Location: scarborough	well when my gunsmith installed my my metal body he did cut my crane stock wire to pull the gun apart...and then sodered the tip back...i guess that was the problem __________________

March 13th, 2006, 19:38	#7
Jar\|-\|ead Banned Trader rating Join Date: Dec 2005	is your gunsmith by anychance 6mm??...

src m4 help

Doctor's Corner